Brake line flare set
This flaring set is suitable for double and single flares of copper, aluminum and mild steel brake lines and brass tubes up to 45 degrees.
Content:
5 adapters in the sizes = 3/16", 1/4", 5/16", 3/8" and 1/2" (4.8, 6.4, 7.9,9.5 and 12.7mm)
pipe holder
spreader
Truck compression gauge / compression test set
This compression test set is suitable for checking the condition of a diesel engine. With no fewer than 7 adapters, the set is suitable for almost all truck diesel engines.The set consists of a pressure gauge with hose, a 90 degree fitting and 7 adapters.The pressure gaug is clearly legible, has 2 scales, a vent valve, a range of 0 - 70bar (0 - 1000psi) and a flexible hose of 360mm with a quick coupling at the end. The 7 adapters can easily be connected here. The 90 degree fitting ensures that hard to reach places are also accessible.Furthermore, the compression meter is equipped with a built-in resetter.
Spark plug adapters:
M10 x 1.0 x 68mm
M10 x 1.25 x 54mm
M10 x 1.25 x 68mm
M12 x 1.25 x 45mm
Nozzle adapters:
M18 x 1.5
M24 x 1.5
M24 x 2.0
This flaring set is suitable for double and single collars of copper, aluminum and mild steel brake lines and brass pipes up to 45 degrees.
pipe holder with metric sizes = 6, 8, 10, 12, 16 and 19mm
pipe holder with inch sizes = 1/4", 5/16", 3/8", 1/2", 5/8" and 3/4"
pipe cutter
Portable air compressor 12V - 12V- air flow rate = 71L/min @ 0 bar - max. power consumption = 30amp - permanent magnet motor - tank capacity = 5,7ltr - max. working pressure = 105psi / 7bar - duty cycle = 33% - max. surrounding temp. = 70 degrees Celcius - min. surrounding temp. -70 degrees Celcius - automatic shut off valve Including tyre gun, couplers, hose and filters
Oil filter caps / oil filter cap set / oil filter disassembly set
This set is suitable for mounting and dismounting almost any oil filter from a large number of types of cars and motorcycles.Caps with 14, 15, 30 and 36P are suitable for all filters from 65mm to 100mm.\
drive = 3/8"
adaptor 1/2" to 3/8"
Sizes caps:
65mm 14P = Toyota / Nissan
65 / 67mm 14P = Ford / Mazda
68mm 14P = Mazda / Ford / Subaru
73mm 14P = Toyota / Audi / Rover / Lexus / Austin
74 / 76mm 15P = VW / Audi / GM / Mercedes / Opel
75 / 77mm 15P = Fiat / Renault
76mm 14P = Motorcraft / Ford
76mm 30P = Fiat / Lancia
80mm 15P = Mazda / Subaru / Toyota / Honda / Nissan
80 / 82mm 15P = Volvo
90mm 15P = Fiat
93mm 15P = Nissan / VW / Porsche / Renault / Honda / Audi
93mm 36P = Ford / Motorcraft
100mm 15P = Isuzu / Mitsubishi
Handy remover set This set is ideal for assembling or disassembling upholstery without damaging the car paint. Various types and models for rubber seals, dashboard, door panels, switches etc.
Torque multiplier
including 2 sockets 32mm and 33mm
- total length = 380mm
- maximum safe output = 5800N/M
- trans-speed ratio = 1:78
- connection = 1''
- total length = 330mm
- maximum safe output = 3800N/M
- trans-speed ratio = 1:58
Portable bead breaker / combi bead breaker
This Mammuth bead breaker is suitable for changing tires without removing without removing the wheel by pressing the tire of the rim.
clam capacity = 4 ton
press capacity = 5 ton
use with hydraulic pump, /- 600bar
working range up to 125mm / 5 inch
Torque mulitiplier 1/2 to 3/4 output 3:1 - input = 1/2" ( 1.27cm ) drive (f) - max = 460nm/340 ft-lb - output = 3/4" ( 1.9cm ) drive (m) - max = 1400nm/1000ft-lb - output/input = 3/1
